Attempt at fixing compile error

firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/pP_config.cpp

@@ -2,18 +2,6 @@
 #include "pP_function.h"
 #include <EEPROM.h>
 
-int GAIN_FACTOR = GAIN_FACTOR_DEFAULT; // Gain adjustment factor. 0=3x, 1=3.5x, 2=4.33x, 3=6x, 4=11x
-int followerThrs = FOLLOWER_THRESHOLD_DEFAULT;
-int compThrs = COMP_THRESHOLD_DEFAULT;
-int LOOP_DUR = LOOP_DUR_DEFAULT; // duration of time between ADC checks and other loop functions
-int TRG_DUR = TRG_DUR_DEFAULT;   // duration of the Z-axis pulse sent, in ms
-int Hyst = HYST_DEFAULT;         // Hysteresis value for ADC measurements
-int LOGIC = LOGIC_DEFAULT;      // Trigger output logic (active low or active high)
-int PZDET = PZDET_DEFAULT;      // Enable/disable piezo connection detection
-int Debug = 0;
-long voltMeterConstant = VM_CONST_DEFAULT;
-uint8_t pP_i2c_address = 0xa0;
-
 /*------------------------------------------------*/
 void eraseEEPROM() {
 	

firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/pP_config.h

@@ -5,21 +5,15 @@
 
 #define GAIN_FACTOR_DEFAULT 2 // Gain adjustment factor. 0=3x, 1=3.5x, 2=4.33x, 3=6x, 4=11x
 #define GAIN_FACTOR_ADDRESS 0
-#if !(defined(GAIN_FACTOR))
- extern int GAIN_FACTOR; 
-#endif
+int GAIN_FACTOR = GAIN_FACTOR_DEFAULT;
 
 #define FOLLOWER_THRESHOLD_DEFAULT 1450 // Voltage follower default voltage in mV
 #define FOLLOWER_THRESHOLD_ADDRESS 4
-#if !(defined(followerThrs))
-  extern int followerThrs;
-#endif
+int followerThrs = 1450;
 
 #define COMP_THRESHOLD_DEFAULT 2850 // Comparatore Vref default voltage in mV
 #define COMP_THRESHOLD_ADDRESS 8
-#if !(defined(compThrs))
-  extern int compThrs;
-#endif
+int compThrs = COMP_THRESHOLD_DEFAULT;
 
 #ifndef InitCount
 #define InitCount 6 // Number of times to blink the LED on start
@@ -27,49 +21,33 @@
 
 #define LOOP_DUR_DEFAULT 50 // duration of time between ADC checks and other loop functions
 #define LOOP_DUR_ADDRESS 12
-#if !(defined(LOOP_DUR))
-  extern int LOOP_DUR; 
-#endif
+int LOOP_DUR = LOOP_DUR_DEFAULT;
 
 #define TRG_DUR_DEFAULT 20 // duration of the Z-axis pulse sent, in ms
 #define TRG_DUR_ADDRESS 16
-#if !(defined(TRG_DUR))
-  extern int TRG_DUR; 
-#endif
+int TRG_DUR = TRG_DUR_DEFAULT;
 
 #define HYST_DEFAULT 20
 #define HYST_ADDRESS 20
-#if !(defined(Hyst))
-  extern int Hyst; // Hysteresis value for ADC measurements
-#endif
+int Hyst = HYST_DEFAULT; // Hysteresis value for ADC measurements
 
 #define LOGIC_DEFAULT 1
 #define LOGIC_ADDRESS 32
-#if !(defined(LOGIC))
-  extern int LOGIC; // Trigger logic scheme, Active LOW is default
-#endif
+int LOGIC = LOGIC_DEFAULT; // Trigger logic scheme, Active LOW is default
 
 #define PZDET_DEFAULT 0
 #define PZDET_ADDRESS 26
-#if !(defined(PZDET))
-  extern int PZDET; // Enable or disable piezo connection detection, default is off
-#endif
+int PZDET = PZDET_DEFAULT; // Enable or disable piezo connection detection, default is off
 
-#if !(defined(Debug))
-  extern int Debug;
-#endif
+int Debug = 0;
 
 #define VM_CONST_ADDRESS 28
 #define VM_CONST_DEFAULT 1125300L
-#if !(defined(voltMeterConstant))
-  extern long voltMeterConstant; // For fine tuning input voltage sense
-#endif
+long voltMeterConstant = VM_CONST_DEFAULT; // For fine tuning input voltage sense
 
 #ifdef I2C_INPUT
 #define I2C_SLAVE_ADDRESS 24
-  #if !(defined(pP_i2c_address))
-    extern uint8_t pP_i2c_address;     // I2C Bus Address
-  #endif
+uint8_t pP_i2c_address = 0xa0; // I2C Bus Address
 #endif // I2C_INPUT
 
 void eraseEEPROM();

firmware/AVR-Source/Pyr0_Piezo_Sensor_v2.x.x/src/pP_function.h

@@ -10,6 +10,7 @@
 #define PP_FUNCTION_H
 
 #include "Arduino.h"
+#include "pP_config.h"
 #include "pP_volatile.h"
 #include "pP_pins.h"
 #include "stdint.h"