diff --git a/scripts/avrdude.conf b/scripts/avrdude.conf
index 657f952..5c9d38d 100644
--- a/scripts/avrdude.conf
+++ b/scripts/avrdude.conf
@@ -2430,3 +2430,14 @@ part parent "m328"
           "x x x x x x x x x x x x i i i i";
     ;
 ;
+
+# Linux GPIO definitions for avrdude & Raspberry Picoweb
+programmer
+  id    = "pi_spi";
+  desc  = "Use the Linux sysfs interface to bitbang GPIO lines";
+  type  = "linuxgpio";
+  reset = 12;
+  sck   = 24;
+  mosi  = 23;
+  miso  = 18;
+;
\ No newline at end of file
diff --git a/scripts/bootloader/MiniCore-avrdude.conf b/scripts/bootloader/MiniCore-avrdude.conf
new file mode 100644
index 0000000..5c9d38d
--- /dev/null
+++ b/scripts/bootloader/MiniCore-avrdude.conf
@@ -0,0 +1,2443 @@
+# $Id: avrdude.conf.in 1371 2016-02-15 20:15:07Z joerg_wunsch $ -*- text -*-
+#
+# AVRDUDE Configuration File
+#
+# This file contains configuration data used by AVRDUDE which describes
+# the programming hardware pinouts and also provides part definitions.
+# AVRDUDE's "-C" command line option specifies the location of the
+# configuration file.  The "-c" option names the programmer configuration
+# which must match one of the entry's "id" parameter.  The "-p" option
+# identifies which part AVRDUDE is going to be programming and must match
+# one of the parts' "id" parameter.
+#
+# DO NOT MODIFY THIS FILE.  Modifications will be overwritten the next
+# time a "make install" is run.  For user-specific additions, use the
+# "-C +filename" commandline option.
+#
+# Possible entry formats are:
+#
+#   programmer
+#       parent <id>                                 # optional parent
+#       id       = <id1> [, <id2> [, <id3>] ...] ;  # <idN> are quoted strings
+#       desc     = <description> ;                  # quoted string
+#       type     = <type>;                          # programmer type, quoted string
+#                          # supported programmer types can be listed by "-c ?type"
+#       connection_type = parallel | serial | usb
+#       baudrate = <num> ;                          # baudrate for avr910-programmer
+#       vcc      = <num1> [, <num2> ... ] ;         # pin number(s)
+#       buff     = <num1> [, <num2> ... ] ;         # pin number(s)
+#       reset    = <num> ;                          # pin number
+#       sck      = <num> ;                          # pin number
+#       mosi     = <num> ;                          # pin number
+#       miso     = <num> ;                          # pin number
+#       errled   = <num> ;                          # pin number
+#       rdyled   = <num> ;                          # pin number
+#       pgmled   = <num> ;                          # pin number
+#       vfyled   = <num> ;                          # pin number
+#       usbvid   = <hexnum>;                        # USB VID (Vendor ID)
+#       usbpid   = <hexnum> [, <hexnum> ...]        # USB PID (Product ID) (1)
+#       usbdev   = <interface>;                     # USB interface or other device info 
+#       usbvendor = <vendorname>;                   # USB Vendor Name
+#       usbproduct = <productname>;                 # USB Product Name
+#       usbsn    = <serialno>;                      # USB Serial Number
+#
+#        To invert a bit, use = ~ <num>, the spaces are important.
+#        For a pin list all pins must be inverted.
+#        A single pin can be specified as usual = ~ <num>, for lists
+#        specify it as follows = ~ ( <num> [, <num2> ... ] ) .
+#
+#        (1) Not all programmer types can process a list of PIDs.
+#     ;
+#
+#   part
+#       id               = <id> ;                 # quoted string
+#       desc             = <description> ;        # quoted string
+#       has_jtag         = <yes/no> ;             # part has JTAG i/f
+#       has_debugwire    = <yes/no> ;             # part has debugWire i/f
+#       has_pdi          = <yes/no> ;             # part has PDI i/f
+#       has_tpi          = <yes/no> ;             # part has TPI i/f
+#       devicecode       = <num> ;            # deprecated, use stk500_devcode
+#       stk500_devcode   = <num> ;                # numeric
+#       avr910_devcode   = <num> ;                # numeric
+#       signature        = <num> <num> <num> ;    # signature bytes
+#       usbpid           = <num> ;                # DFU USB PID
+#       chip_erase_delay = <num> ;                # micro-seconds
+#       reset            = dedicated | io;
+#       retry_pulse      = reset | sck;
+#       pgm_enable       = <instruction format> ;
+#       chip_erase       = <instruction format> ;
+#       chip_erase_delay = <num> ;                # chip erase delay (us)
+#       # STK500 parameters (parallel programming IO lines)
+#       pagel            = <num> ;                # pin name in hex, i.e., 0xD7
+#       bs2              = <num> ;                # pin name in hex, i.e., 0xA0
+#       serial           = <yes/no> ;             # can use serial downloading
+#       parallel         = <yes/no/pseudo>;       # can use par. programming
+#       # STK500v2 parameters, to be taken from Atmel's XML files
+#       timeout          = <num> ;
+#       stabdelay        = <num> ;
+#       cmdexedelay      = <num> ;
+#       synchloops       = <num> ;
+#       bytedelay        = <num> ;
+#       pollvalue        = <num> ;
+#       pollindex        = <num> ;
+#       predelay         = <num> ;
+#       postdelay        = <num> ;
+#       pollmethod       = <num> ;
+#       mode             = <num> ;
+#       delay            = <num> ;
+#       blocksize        = <num> ;
+#       readsize         = <num> ;
+#       hvspcmdexedelay  = <num> ;
+#       # STK500v2 HV programming parameters, from XML
+#       pp_controlstack  = <num>, <num>, ...;   # PP only
+#       hvsp_controlstack = <num>, <num>, ...;  # HVSP only
+#       hventerstabdelay = <num>;
+#       progmodedelay    = <num>;               # PP only
+#       latchcycles      = <num>;
+#       togglevtg        = <num>;
+#       poweroffdelay    = <num>;
+#       resetdelayms     = <num>;
+#       resetdelayus     = <num>;
+#       hvleavestabdelay = <num>;
+#       resetdelay       = <num>;
+#       synchcycles      = <num>;               # HVSP only
+#       chiperasepulsewidth = <num>;            # PP only
+#       chiperasepolltimeout = <num>;
+#       chiperasetime    = <num>;               # HVSP only
+#       programfusepulsewidth = <num>;          # PP only
+#       programfusepolltimeout = <num>;
+#       programlockpulsewidth = <num>;          # PP only
+#       programlockpolltimeout = <num>;
+#       # JTAG ICE mkII parameters, also from XML files
+#       allowfullpagebitstream = <yes/no> ;
+#       enablepageprogramming = <yes/no> ;
+#       idr              = <num> ;                # IO addr of IDR (OCD) reg.
+#       rampz            = <num> ;                # IO addr of RAMPZ reg.
+#       spmcr            = <num> ;                # mem addr of SPMC[S]R reg.
+#       eecr             = <num> ;                # mem addr of EECR reg.
+#                                                 # (only when != 0x3c)
+#       is_at90s1200     = <yes/no> ;             # AT90S1200 part
+#       is_avr32         = <yes/no> ;             # AVR32 part
+#
+#       memory <memtype>
+#           paged           = <yes/no> ;          # yes / no
+#           size            = <num> ;             # bytes
+#           page_size       = <num> ;             # bytes
+#           num_pages       = <num> ;             # numeric
+#           min_write_delay = <num> ;             # micro-seconds
+#           max_write_delay = <num> ;             # micro-seconds
+#           readback_p1     = <num> ;             # byte value
+#           readback_p2     = <num> ;             # byte value
+#           pwroff_after_write = <yes/no> ;       # yes / no
+#           read            = <instruction format> ;
+#           write           = <instruction format> ;
+#           read_lo         = <instruction format> ;
+#           read_hi         = <instruction format> ;
+#           write_lo        = <instruction format> ;
+#           write_hi        = <instruction format> ;
+#           loadpage_lo     = <instruction format> ;
+#           loadpage_hi     = <instruction format> ;
+#           writepage       = <instruction format> ;
+#         ;
+#     ;
+#
+# If any of the above parameters are not specified, the default value
+# of 0 is used for numerics or the empty string ("") for string
+# values.  If a required parameter is left empty, AVRDUDE will
+# complain.
+#
+# Parts can also inherit parameters from previously defined parts
+# using the following syntax. In this case specified integer and 
+# string values override parameter values from the parent part. New 
+# memory definitions are added to the definitions inherited from the 
+# parent.
+#
+#   part parent <id>                              # quoted string
+#       id               = <id> ;                 # quoted string
+#       <any set of other parameters from the list above>
+#     ;
+#
+# NOTES:
+#   * 'devicecode' is the device code used by the STK500 (see codes 
+#       listed below)
+#   * Not all memory types will implement all instructions.
+#   * AVR Fuse bits and Lock bits are implemented as a type of memory.
+#   * Example memory types are:
+#       "flash", "eeprom", "fuse", "lfuse" (low fuse), "hfuse" (high
+#       fuse), "signature", "calibration", "lock"
+#   * The memory type specified on the avrdude command line must match
+#     one of the memory types defined for the specified chip.
+#   * The pwroff_after_write flag causes avrdude to attempt to
+#     power the device off and back on after an unsuccessful write to
+#     the affected memory area if VCC programmer pins are defined.  If
+#     VCC pins are not defined for the programmer, a message
+#     indicating that the device needs a power-cycle is printed out.
+#     This flag was added to work around a problem with the
+#     at90s4433/2333's; see the at90s4433 errata at:
+#
+#         http://www.atmel.com/dyn/resources/prod_documents/doc1280.pdf
+#
+# INSTRUCTION FORMATS
+#
+#    Instruction formats are specified as a comma seperated list of
+#    string values containing information (bit specifiers) about each
+#    of the 32 bits of the instruction.  Bit specifiers may be one of
+#    the following formats:
+#
+#       '1'  = the bit is always set on input as well as output
+#
+#       '0'  = the bit is always clear on input as well as output
+#
+#       'x'  = the bit is ignored on input and output
+#
+#       'a'  = the bit is an address bit, the bit-number matches this bit
+#              specifier's position within the current instruction byte
+#
+#       'aN' = the bit is the Nth address bit, bit-number = N, i.e., a12
+#              is address bit 12 on input, a0 is address bit 0.
+#
+#       'i'  = the bit is an input data bit
+#
+#       'o'  = the bit is an output data bit
+#
+#    Each instruction must be composed of 32 bit specifiers.  The
+#    instruction specification closely follows the instruction data
+#    provided in Atmel's data sheets for their parts.
+#
+# See below for some examples.
+#
+#
+# The following are STK500 part device codes to use for the
+# "devicecode" field of the part.  These came from Atmel's software
+# section avr061.zip which accompanies the application note
+# AVR061 available from:
+#
+#      http://www.atmel.com/dyn/resources/prod_documents/doc2525.pdf
+#
+
+#define ATTINY10    0x10  /* the _old_ one that never existed! */
+#define ATTINY11    0x11
+#define ATTINY12    0x12
+#define ATTINY15    0x13
+#define ATTINY13    0x14
+
+#define ATTINY22    0x20
+#define ATTINY26    0x21
+#define ATTINY28    0x22
+#define ATTINY2313  0x23
+
+#define AT90S1200   0x33
+
+#define AT90S2313   0x40
+#define AT90S2323   0x41
+#define AT90S2333   0x42
+#define AT90S2343   0x43
+
+#define AT90S4414   0x50
+#define AT90S4433   0x51
+#define AT90S4434   0x52
+#define ATMEGA48    0x59
+
+#define AT90S8515   0x60
+#define AT90S8535   0x61
+#define AT90C8534   0x62
+#define ATMEGA8515  0x63
+#define ATMEGA8535  0x64
+
+#define ATMEGA8     0x70
+#define ATMEGA88    0x73
+#define ATMEGA168   0x86
+
+#define ATMEGA161   0x80
+#define ATMEGA163   0x81
+#define ATMEGA16    0x82
+#define ATMEGA162   0x83
+#define ATMEGA169   0x84
+
+#define ATMEGA323   0x90
+#define ATMEGA32    0x91
+
+#define ATMEGA64    0xA0
+
+#define ATMEGA103   0xB1
+#define ATMEGA128   0xB2
+#define AT90CAN128  0xB3
+#define AT90CAN64   0xB3
+#define AT90CAN32   0xB3
+
+#define AT86RF401   0xD0
+
+#define AT89START   0xE0
+#define AT89S51	    0xE0
+#define AT89S52	    0xE1
+
+# The following table lists the devices in the original AVR910
+# appnote:
+# |Device |Signature | Code |
+# +-------+----------+------+
+# |tiny12 | 1E 90 05 | 0x55 |
+# |tiny15 | 1E 90 06 | 0x56 |
+# |       |          |      |
+# | S1200 | 1E 90 01 | 0x13 |
+# |       |          |      |
+# | S2313 | 1E 91 01 | 0x20 |
+# | S2323 | 1E 91 02 | 0x48 |
+# | S2333 | 1E 91 05 | 0x34 |
+# | S2343 | 1E 91 03 | 0x4C |
+# |       |          |      |
+# | S4414 | 1E 92 01 | 0x28 |
+# | S4433 | 1E 92 03 | 0x30 |
+# | S4434 | 1E 92 02 | 0x6C |
+# |       |          |      |
+# | S8515 | 1E 93 01 | 0x38 |
+# | S8535 | 1E 93 03 | 0x68 |
+# |       |          |      |
+# |mega32 | 1E 95 01 | 0x72 |
+# |mega83 | 1E 93 05 | 0x65 |
+# |mega103| 1E 97 01 | 0x41 |
+# |mega161| 1E 94 01 | 0x60 |
+# |mega163| 1E 94 02 | 0x64 |
+
+# Appnote AVR109 also has a table of AVR910 device codes, which
+# lists:
+# dev         avr910   signature
+# ATmega8     0x77     0x1E 0x93 0x07
+# ATmega8515  0x3B     0x1E 0x93 0x06
+# ATmega8535  0x6A     0x1E 0x93 0x08
+# ATmega16    0x75     0x1E 0x94 0x03
+# ATmega162   0x63     0x1E 0x94 0x04
+# ATmega163   0x66     0x1E 0x94 0x02
+# ATmega169   0x79     0x1E 0x94 0x05
+# ATmega32    0x7F     0x1E 0x95 0x02
+# ATmega323   0x73     0x1E 0x95 0x01
+# ATmega64    0x46     0x1E 0x96 0x02
+# ATmega128   0x44     0x1E 0x97 0x02
+#
+# These codes refer to "BOOT" device codes which are apparently
+# different than standard device codes, for whatever reasons
+# (often one above the standard code).
+
+# There are several extended versions of AVR910 implementations around
+# in the Internet.  These add the following codes (only devices that
+# actually exist are listed):
+
+# ATmega8515	0x3A
+# ATmega128	0x43
+# ATmega64	0x45
+# ATtiny26	0x5E
+# ATmega8535	0x69
+# ATmega32	0x72
+# ATmega16	0x74
+# ATmega8	0x76
+# ATmega169	0x78
+
+#
+# Overall avrdude defaults; suitable for ~/.avrduderc
+#
+default_parallel   = "@DEFAULT_PAR_PORT@";
+default_serial     = "@DEFAULT_SER_PORT@";
+# default_bitclock = 2.5;
+
+# Turn off safemode by default
+#default_safemode  = no;
+
+
+#
+# PROGRAMMER DEFINITIONS
+#
+
+# http://wiring.org.co/
+# Basically STK500v2 protocol, with some glue to trigger the
+# bootloader.
+programmer
+  id    = "wiring";
+  desc  = "Wiring";
+  type  = "wiring";
+  connection_type = serial;
+;
+
+programmer
+  id    = "arduino";
+  desc  = "Arduino";
+  type  = "arduino";
+  connection_type = serial;
+;
+# this will interface with the chips on these programmers:
+#
+# http://real.kiev.ua/old/avreal/en/adapters
+# http://www.amontec.com/jtagkey.shtml, jtagkey-tiny.shtml
+# http://www.olimex.com/dev/arm-usb-ocd.html, arm-usb-tiny.html
+# http://www.ethernut.de/en/hardware/turtelizer/index.html
+# http://elk.informatik.fh-augsburg.de/hhweb/doc/openocd/usbjtag/usbjtag.html
+# http://dangerousprototypes.com/docs/FT2232_breakout_board
+# http://www.ftdichip.com/Products/Modules/DLPModules.htm,DLP-2232*,DLP-USB1232H
+# http://flashrom.org/FT2232SPI_Programmer
+# 
+# The drivers will look for a specific device and use the first one found.
+# If you have mulitple devices, then look for unique information (like SN)
+# And fill that in here.
+#
+# Note that the pin numbers for the main ISP signals (reset, sck,
+# mosi, miso) are fixed and cannot be changed, since they must match
+# the way the Multi-Protocol Synchronous Serial Engine (MPSSE) of
+# these FTDI ICs has been designed.
+
+programmer
+  id         = "avrftdi";
+  desc       = "FT2232D based generic programmer";
+  type       = "avrftdi";
+  connection_type = usb;
+  usbvid     = 0x0403;
+  usbpid     = 0x6010;
+  usbvendor  = "";
+  usbproduct = "";
+  usbdev     = "A";
+  usbsn      = "";
+#ISP-signals - lower ADBUS-Nibble (default)
+  reset  = 3;
+  sck    = 0;
+  mosi   = 1;
+  miso   = 2;
+#LED SIGNALs - higher ADBUS-Nibble
+#  errled = 4;
+#  rdyled = 5;
+#  pgmled = 6;
+#  vfyled = 7;
+#Buffer Signal - ACBUS - Nibble
+#  buff   = 8;
+;
+# This is an implementation of the above with a buffer IC (74AC244) and
+# 4 LEDs directly attached, all active low.
+programmer
+  id         = "2232HIO";
+  desc       = "FT2232H based generic programmer";
+  type       = "avrftdi";
+  connection_type = usb;
+  usbvid     = 0x0403;
+# Note: This PID is reserved for generic H devices and 
+# should be programmed into the EEPROM
+#  usbpid     = 0x8A48;
+  usbpid     = 0x6010;
+  usbdev     = "A";
+  usbvendor  = "";
+  usbproduct = "";
+  usbsn      = "";
+#ISP-signals 
+  reset  = 3;
+  sck    = 0;
+  mosi   = 1;
+  miso   = 2;
+  buff   = ~4;
+#LED SIGNALs 
+  errled = ~ 11;
+  rdyled = ~ 14;
+  pgmled = ~ 13;
+  vfyled = ~ 12;
+;
+
+#The FT4232H can be treated as FT2232H, but it has a different USB
+#device ID of 0x6011.
+programmer parent "avrftdi"
+  id         = "4232h";
+  desc       = "FT4232H based generic programmer";
+  usbpid     = 0x6011;
+;
+
+programmer
+  id         = "jtagkey";
+  desc       = "Amontec JTAGKey, JTAGKey-Tiny and JTAGKey2";
+  type       = "avrftdi";
+  connection_type = usb;
+  usbvid     = 0x0403;
+# Note: This PID is used in all JTAGKey variants
+  usbpid     = 0xCFF8;
+  usbdev     = "A";
+  usbvendor  = "";
+  usbproduct = "";
+  usbsn      = "";
+#ISP-signals => 20 - Pin connector on JTAGKey
+  reset  = 3; # TMS 7 violet
+  sck    = 0; # TCK 9 white
+  mosi   = 1; # TDI 5 green
+  miso   = 2; # TDO 13 orange
+  buff   = ~4;
+# VTG           VREF 1 brown with red tip
+# GND           GND 20 black
+# The colors are on the 20 pin breakout cable
+# from Amontec
+;
+
+# UM232H module from FTDI and Glyn.com.au.
+# See helix.air.net.au for detailed usage information.
+# J1: Connect pin 2 and 3 for USB power.
+# J2: Connect pin 2 and 3 for USB power.
+# J2: Pin 7 is SCK
+#   : Pin 8 is MOSI
+#   : Pin 9 is MISO
+#   : Pin 11 is RST
+#   : Pin 6 is ground
+# Use the -b flag to set the SPI clock rate eg -b 3750000 is the fastest I could get
+# a 16MHz Atmega1280 to program reliably.  The 232H is conveniently 5V tolerant.
+programmer
+  id         = "UM232H";
+  desc       = "FT232H based module from FTDI and Glyn.com.au";
+  type       = "avrftdi";
+  usbvid     = 0x0403;
+# Note: This PID is reserved for generic 232H devices and
+# should be programmed into the EEPROM
+  usbpid     = 0x6014;
+  usbdev     = "A";
+  usbvendor  = "";
+  usbproduct = "";
+  usbsn      = "";
+#ISP-signals
+  sck    = 0;
+  mosi   = 1;
+  miso   = 2;
+  reset  = 3;
+;
+
+# C232HM module from FTDI and Glyn.com.au.
+# : Orange is SCK
+# : Yellow is MOSI
+# : Green is MISO
+# : Brown is RST
+# : Black is ground
+# Use the -b flag to set the SPI clock rate eg -b 3750000 is the fastest I could get
+# a 16MHz Atmega1280 to program reliably.  The 232H is conveniently 5V tolerant.
+programmer
+  id         = "C232HM";
+  desc       = "FT232H based module from FTDI and Glyn.com.au";
+  type       = "avrftdi";
+  usbvid     = 0x0403;
+# Note: This PID is reserved for generic 232H devices and
+# should be programmed into the EEPROM
+  usbpid     = 0x6014;
+  usbdev     = "A";
+  usbvendor  = "";
+  usbproduct = "";
+  usbsn      = "";
+#ISP-signals
+  sck    = 0;
+  mosi   = 1;
+  miso   = 2;
+  reset  = 3;
+;
+
+
+# On the adapter you can read "O-Link". On the PCB is printed "OpenJTAG v3.1"
+# You can find it as "OpenJTAG ARM JTAG USB" in the internet. 
+# (But there are also several projects called Open JTAG, eg. 
+# http://www.openjtag.org, which are completely different.)
+#   http://www.100ask.net/shop/english.html (website seems to be outdated)
+#   http://item.taobao.com/item.htm?id=1559277013
+#   http://www.micro4you.com/store/openjtag-arm-jtag-usb.html (schematics!)
+# some other sources which call it O-Link
+#   http://www.andahammer.com/olink/
+#   http://www.developmentboard.net/31-o-link-debugger.html
+#   http://armwerks.com/catalog/o-link-debugger-copy/
+# or just have a look at ebay ...
+# It is basically the same entry as jtagkey with different usb ids.
+programmer parent "jtagkey"
+  id         = "o-link";
+  desc       = "O-Link, OpenJTAG from www.100ask.net";
+  usbvid     = 0x1457;
+  usbpid     = 0x5118;
+  usbvendor  = "www.100ask.net";
+  usbproduct = "USB<=>JTAG&RS232";
+;
+
+# http://wiki.openmoko.org/wiki/Debug_Board_v3
+programmer
+  id    = "openmoko";
+  desc  = "Openmoko debug board (v3)";
+  type  = "avrftdi";
+  usbvid     = 0x1457;
+  usbpid    = 0x5118;
+  usbdev = "A";
+  usbvendor  = "";
+  usbproduct = "";
+  usbsn      = "";
+  reset  = 3; # TMS 7
+  sck    = 0; # TCK 9
+  mosi   = 1; # TDI 5
+  miso   = 2; # TDO 13
+;
+
+# Only Rev. A boards.
+# Schematic and user manual: http://www.cs.put.poznan.pl/wswitala/download/pdf/811EVBK.pdf
+programmer
+  id         = "lm3s811";
+  desc       = "Luminary Micro LM3S811 Eval Board (Rev. A)";
+  type       = "avrftdi";
+  connection_type = usb;
+  usbvid     = 0x0403;
+  usbpid     = 0xbcd9;
+  usbvendor  = "LMI";
+  usbproduct = "LM3S811 Evaluation Board";
+  usbdev     = "A";
+  usbsn      = "";
+#ISP-signals - lower ACBUS-Nibble (default)
+  reset  = 3;
+  sck    = 0;
+  mosi   = 1;
+  miso   = 2;
+# Enable correct buffers
+  buff   = 7;
+;
+
+# submitted as bug #46020
+programmer
+  id     = "tumpa";
+  desc   = "TIAO USB Multi-Protocol Adapter";
+  type   = "avrftdi";
+  connection_type = usb;
+  usbvid = 0x0403;
+  usbpid = 0x8A98;
+  usbdev = "A";
+  usbvendor = "TIAO";
+  usbproduct = "";
+  usbsn  = "";
+  sck    = 0; # TCK 9
+  mosi   = 1; # TDI 5
+  miso   = 2; # TDO 13
+  reset  = 3; # TMS 7
+;
+
+programmer
+  id    = "avrisp";
+  desc  = "Atmel AVR ISP";
+  type  = "stk500";
+  connection_type = serial;
+;
+
+programmer
+  id    = "avrispv2";
+  desc  = "Atmel AVR ISP V2";
+  type  =  "stk500v2";
+  connection_type = serial;
+;
+
+programmer
+  id    = "avrispmkII";
+  desc  = "Atmel AVR ISP mkII";
+  type  =  "stk500v2";
+  connection_type = usb;
+;
+
+programmer parent "avrispmkII"
+  id    = "avrisp2";
+;
+
+programmer
+  id    = "buspirate";
+  desc  = "The Bus Pirate";
+  type  = "buspirate";
+  connection_type = serial;
+;
+
+programmer
+  id    = "buspirate_bb";
+  desc  = "The Bus Pirate (bitbang interface, supports TPI)";
+  type  = "buspirate_bb";
+  connection_type = serial;
+  # pins are bits in bitbang byte (numbers are 87654321)
+  # 1|POWER|PULLUP|AUX|MOSI|CLK|MISO|CS
+  reset  = 1;
+  sck    = 3;
+  mosi   = 4;
+  miso   = 2;
+  #vcc    = 7; This is internally set independent of this setting.
+;
+
+# This is supposed to be the "default" STK500 entry.
+# Attempts to select the correct firmware version
+# by probing for it.  Better use one of the entries
+# below instead.
+programmer
+  id    = "stk500";
+  desc  = "Atmel STK500";
+  type  = "stk500generic";
+  connection_type = serial;
+;
+
+programmer
+  id    = "stk500v1";
+  desc  = "Atmel STK500 Version 1.x firmware";
+  type  = "stk500";
+  connection_type = serial;
+;
+
+programmer
+  id    = "mib510";
+  desc  = "Crossbow MIB510 programming board";
+  type  = "stk500";
+  connection_type = serial;
+;
+
+programmer
+  id    = "stk500v2";
+  desc  = "Atmel STK500 Version 2.x firmware";
+  type  = "stk500v2";
+  connection_type = serial;
+;
+
+programmer
+  id    = "stk500pp";
+  desc  = "Atmel STK500 V2 in parallel programming mode";
+  type  = "stk500pp";
+  connection_type = serial;
+;
+
+programmer
+  id    = "stk500hvsp";
+  desc  = "Atmel STK500 V2 in high-voltage serial programming mode";
+  type  = "stk500hvsp";
+  connection_type = serial;
+;
+
+programmer
+  id    = "stk600";
+  desc  = "Atmel STK600";
+  type  = "stk600";
+  connection_type = usb;
+;
+
+programmer
+  id    = "stk600pp";
+  desc  = "Atmel STK600 in parallel programming mode";
+  type  = "stk600pp";
+  connection_type = usb;
+;
+
+programmer
+  id    = "stk600hvsp";
+  desc  = "Atmel STK600 in high-voltage serial programming mode";
+  type  = "stk600hvsp";
+  connection_type = usb;
+;
+
+programmer
+  id    = "avr910";
+  desc  = "Atmel Low Cost Serial Programmer";
+  type  = "avr910";
+  connection_type = serial;
+;
+
+programmer
+  id    = "ft245r";
+  desc  = "FT245R Synchronous BitBang";
+  type  = "ftdi_syncbb";
+  connection_type = usb;
+  miso  = 1; # D1
+  sck   = 0; # D0
+  mosi  = 2; # D2
+  reset = 4; # D4
+;
+
+programmer
+  id    = "ft232r";
+  desc  = "FT232R Synchronous BitBang";
+  type  = "ftdi_syncbb";
+  connection_type = usb;
+  miso  = 1;  # RxD
+  sck   = 0;  # TxD
+  mosi  = 2;  # RTS
+  reset = 4;  # DTR
+;
+
+# see http://www.bitwizard.nl/wiki/index.php/FTDI_ATmega
+programmer
+  id    = "bwmega";
+  desc  = "BitWizard ftdi_atmega builtin programmer";
+  type  = "ftdi_syncbb";
+  connection_type = usb;
+  miso  = 5;  # DSR
+  sck   = 6;  # DCD
+  mosi  = 3;  # CTS
+  reset = 7;  # RI
+;
+
+# see http://www.geocities.jp/arduino_diecimila/bootloader/index_en.html
+# Note: pins are numbered from 1!
+programmer
+  id    = "arduino-ft232r";
+  desc  = "Arduino: FT232R connected to ISP";
+  type  = "ftdi_syncbb";
+  connection_type = usb;
+  miso  = 3;  # CTS X3(1)
+  sck   = 5;  # DSR X3(2)
+  mosi  = 6;  # DCD X3(3)
+  reset = 7;  # RI  X3(4)
+;
+
+# website mentioned above uses this id
+programmer parent "arduino-ft232r"
+  id    = "diecimila";
+  desc  = "alias for arduino-ft232r";
+;
+
+# There is a ATmega328P kit PCB called "uncompatino".
+# This board allows ISP via its on-board FT232R.
+# This is designed like Arduino Duemilanove but has no standard ICPS header.
+# Its 4 pairs of pins are shorted to enable ftdi_syncbb.
+# http://akizukidenshi.com/catalog/g/gP-07487/
+# http://akizukidenshi.com/download/ds/akizuki/k6096_manual_20130816.pdf
+programmer
+  id    = "uncompatino";
+  desc  = "uncompatino with all pairs of pins shorted";
+  type  = "ftdi_syncbb";
+  connection_type = usb;
+  miso  = 3; # cts
+  sck   = 5; # dsr
+  mosi  = 6; # dcd
+  reset = 7; # ri
+;
+
+# FTDI USB to serial cable TTL-232R-5V with a custom adapter for ICSP
+# http://www.ftdichip.com/Products/Cables/USBTTLSerial.htm
+# http://www.ftdichip.com/Support/Documents/DataSheets/Cables/DS_TTL-232R_CABLES.pdf
+# For ICSP pinout see for example http://www.atmel.com/images/doc2562.pdf
+# (Figure 1. ISP6PIN header pinout and Table 1. Connections required for ISP ...)
+# TTL-232R GND 1 Black  -> ICPS GND   (pin 6)
+# TTL-232R CTS 2 Brown  -> ICPS MOSI  (pin 4)
+# TTL-232R VCC 3 Red    -> ICPS VCC   (pin 2)
+# TTL-232R TXD 4 Orange -> ICPS RESET (pin 5)
+# TTL-232R RXD 5 Yellow -> ICPS SCK   (pin 3)
+# TTL-232R RTS 6 Green  -> ICPS MISO  (pin 1)
+# Except for VCC and GND, you can connect arbitual pairs as long as 
+# the following table is adjusted.
+programmer
+  id    = "ttl232r";
+  desc  = "FTDI TTL232R-5V with ICSP adapter";
+  type  = "ftdi_syncbb";
+  connection_type = usb;
+  miso  = 2; # rts
+  sck   = 1; # rxd
+  mosi  = 3; # cts
+  reset = 0; # txd
+;
+
+programmer
+  id    = "usbasp";
+  desc  = "USBasp, http://www.fischl.de/usbasp/";
+  type  = "usbasp";
+  connection_type = usb;
+  usbvid     = 0x16C0; # VOTI
+  usbpid     = 0x05DC; # Obdev's free shared PID
+  usbvendor  = "www.fischl.de";
+  usbproduct = "USBasp";
+
+  # following variants are autodetected for id "usbasp"
+
+  # original usbasp from fischl.de
+  # see above "usbasp"
+
+  # old usbasp from fischl.de
+  #usbvid     = 0x03EB; # ATMEL
+  #usbpid     = 0xC7B4; # (unoffical) USBasp
+  #usbvendor  = "www.fischl.de";
+  #usbproduct = "USBasp";
+
+  # NIBObee (only if -P nibobee is given on command line)
+  # see below "nibobee"
+;
+
+programmer
+  id    = "nibobee";
+  desc  = "NIBObee";
+  type  = "usbasp";
+  connection_type = usb;
+  usbvid     = 0x16C0; # VOTI
+  usbpid     = 0x092F; # NIBObee PID
+  usbvendor  = "www.nicai-systems.com";
+  usbproduct = "NIBObee";
+;
+
+programmer
+  id    = "usbasp-clone";
+  desc  = "Any usbasp clone with correct VID/PID";
+  type  = "usbasp";
+  connection_type = usb;
+  usbvid    = 0x16C0; # VOTI
+  usbpid    = 0x05DC; # Obdev's free shared PID
+  #usbvendor  = "";
+  #usbproduct = "";
+;
+
+programmer
+  id    = "usbtiny";
+  desc  = "USBtiny simple USB programmer, http://www.ladyada.net/make/usbtinyisp/";
+  type  = "usbtiny";
+  connection_type = usb;
+  usbvid     = 0x1781;
+  usbpid     = 0x0c9f;
+;
+
+programmer
+  id    = "butterfly";
+  desc  = "Atmel Butterfly Development Board";
+  type  = "butterfly";
+  connection_type = serial;
+;
+
+programmer
+  id    = "arduinoisporg";
+  desc  = "Arduino ISP Programmer";
+  type  = "usbtiny";
+  connection_type = usb;
+  usbvid     = 0x2A03;
+  usbpid     = 0x0049;
+;
+
+programmer
+  id    = "avr109";
+  desc  = "Atmel AppNote AVR109 Boot Loader";
+  type  = "butterfly";
+  connection_type = serial;
+;
+
+programmer
+  id    = "avr911";
+  desc  = "Atmel AppNote AVR911 AVROSP";
+  type  = "butterfly";
+  connection_type = serial;
+;
+ 
+# suggested in http://forum.mikrokopter.de/topic-post48317.html
+programmer
+  id    = "mkbutterfly";
+  desc  = "Mikrokopter.de Butterfly";
+  type  = "butterfly_mk";
+  connection_type = serial;
+;
+
+programmer parent "mkbutterfly"
+  id    = "butterfly_mk";
+;
+
+programmer
+  id    = "jtagmkI";
+  desc  = "Atmel JTAG ICE (mkI)";
+  baudrate = 115200;    # default is 115200
+  type  = "jtagmki";
+  connection_type = serial;
+;
+
+# easier to type
+programmer parent "jtagmkI"
+  id    = "jtag1";
+;
+
+# easier to type
+programmer parent "jtag1"
+  id    = "jtag1slow";
+  baudrate = 19200;
+;
+
+# The JTAG ICE mkII has both, serial and USB connectivity.  As it is
+# mostly used through USB these days (AVR Studio 5 only supporting it
+# that way), we make connection_type = usb the default.  Users are
+# still free to use a serial port with the -P option.
+
+programmer
+  id    = "jtagmkII";
+  desc  = "Atmel JTAG ICE mkII";
+  baudrate = 19200;    # default is 19200
+  type  = "jtagmkii";
+  connection_type = usb;
+;
+
+# easier to type
+programmer parent "jtagmkII"
+  id    = "jtag2slow";
+;
+
+# JTAG ICE mkII @ 115200 Bd
+programmer parent "jtag2slow"
+  id    = "jtag2fast";
+  baudrate = 115200;
+;
+
+# make the fast one the default, people will love that
+programmer parent "jtag2fast"
+  id    = "jtag2";
+;
+
+# JTAG ICE mkII in ISP mode
+programmer
+  id    = "jtag2isp";
+  desc  = "Atmel JTAG ICE mkII in ISP mode";
+  baudrate = 115200;
+  type  = "jtagmkii_isp";
+  connection_type = usb;
+;
+
+# JTAG ICE mkII in debugWire mode
+programmer
+  id    = "jtag2dw";
+  desc  = "Atmel JTAG ICE mkII in debugWire mode";
+  baudrate = 115200;
+  type  = "jtagmkii_dw";
+  connection_type = usb;
+;
+
+# JTAG ICE mkII in AVR32 mode
+programmer
+  id    = "jtagmkII_avr32";
+  desc  = "Atmel JTAG ICE mkII im AVR32 mode";
+  baudrate = 115200;
+  type  = "jtagmkii_avr32";
+  connection_type = usb;
+;
+
+# JTAG ICE mkII in AVR32 mode
+programmer
+  id    = "jtag2avr32";
+  desc  = "Atmel JTAG ICE mkII im AVR32 mode";
+  baudrate = 115200;
+  type  = "jtagmkii_avr32";
+  connection_type = usb;
+;
+
+# JTAG ICE mkII in PDI mode
+programmer
+  id    = "jtag2pdi";
+  desc  = "Atmel JTAG ICE mkII PDI mode";
+  baudrate = 115200;
+  type  = "jtagmkii_pdi";
+  connection_type = usb;
+;
+
+# AVR Dragon in JTAG mode
+programmer
+  id    = "dragon_jtag";
+  desc  = "Atmel AVR Dragon in JTAG mode";
+  baudrate = 115200;
+  type  = "dragon_jtag";
+  connection_type = usb;
+;
+
+# AVR Dragon in ISP mode
+programmer
+  id    = "dragon_isp";
+  desc  = "Atmel AVR Dragon in ISP mode";
+  baudrate = 115200;
+  type  = "dragon_isp";
+  connection_type = usb;
+;
+
+# AVR Dragon in PP mode
+programmer
+  id    = "dragon_pp";
+  desc  = "Atmel AVR Dragon in PP mode";
+  baudrate = 115200;
+  type  = "dragon_pp";
+  connection_type = usb;
+;
+
+# AVR Dragon in HVSP mode
+programmer
+  id    = "dragon_hvsp";
+  desc  = "Atmel AVR Dragon in HVSP mode";
+  baudrate = 115200;
+  type  = "dragon_hvsp";
+  connection_type = usb;
+;
+
+# AVR Dragon in debugWire mode
+programmer
+  id    = "dragon_dw";
+  desc  = "Atmel AVR Dragon in debugWire mode";
+  baudrate = 115200;
+  type  = "dragon_dw";
+  connection_type = usb;
+;
+
+# AVR Dragon in PDI mode
+programmer
+  id    = "dragon_pdi";
+  desc  = "Atmel AVR Dragon in PDI mode";
+  baudrate = 115200;
+  type  = "dragon_pdi";
+  connection_type = usb;
+;
+
+
+programmer
+  id    = "xplainedpro";
+  desc  = "Atmel AVR XplainedPro in JTAG mode";
+  type  = "jtagice3";
+  connection_type = usb;
+  usbpid = 0x2111;
+;
+
+
+programmer
+  id    = "atmelice_pdi";
+  desc  = "Atmel-ICE (ARM/AVR) in PDI mode";
+  type  = "jtagice3_pdi";
+  connection_type = usb;
+  usbpid = 0x2141;
+;
+
+programmer
+  id    = "atmelice_dw";
+  desc  = "Atmel-ICE (ARM/AVR) in debugWIRE mode";
+  type  = "jtagice3_dw";
+  connection_type = usb;
+  usbpid = 0x2141;
+;
+
+programmer
+  id    = "atmelice_isp";
+  desc  = "Atmel-ICE (ARM/AVR) in ISP mode";
+  type  = "jtagice3_isp";
+  connection_type = usb;
+  usbpid = 0x2141;
+;
+
+
+programmer
+  id    = "pavr";
+  desc  = "Jason Kyle's pAVR Serial Programmer";
+  type  = "avr910";
+  connection_type = serial;
+;
+
+programmer
+  id    = "pickit2";
+  desc  = "MicroChip's PICkit2 Programmer";
+  type  = "pickit2";
+  connection_type = usb;
+;
+
+
+programmer
+  id    = "stk200";
+  desc  = "STK200";
+  type  = "par";
+  connection_type = parallel;
+  buff  = 4, 5;
+  sck   = 6;
+  mosi  = 7;
+  reset = 9;
+  miso  = 10;
+;
+
+# The programming dongle used by the popular Ponyprog
+# utility.  It is almost similar to the STK200 one,
+# except that there is a LED indicating that the
+# programming is currently in progress.
+
+programmer parent "stk200"
+  id    = "pony-stk200";
+  desc  = "Pony Prog STK200";
+  pgmled = 8; 
+;
+
+programmer
+  id    = "dt006";
+  desc  = "Dontronics DT006";
+  type  = "par";
+  connection_type = parallel;
+  reset = 4;
+  sck   = 5;
+  mosi  = 2;
+  miso  = 11;
+;
+
+programmer parent "dt006"
+  id    = "bascom";
+  desc  = "Bascom SAMPLE programming cable";
+;
+
+programmer
+  id     = "alf";
+  desc   = "Nightshade ALF-PgmAVR, http://nightshade.homeip.net/";
+  type   = "par";
+  connection_type = parallel;
+  vcc    = 2, 3, 4, 5;
+  buff   = 6;
+  reset  = 7;
+  sck    = 8;
+  mosi   = 9;
+  miso   = 10;
+  errled = 1;
+  rdyled = 14;
+  pgmled = 16;
+  vfyled = 17;
+;
+
+programmer
+  id    = "sp12";
+  desc  = "Steve Bolt's Programmer";
+  type  = "par";
+  connection_type = parallel;
+  vcc   = 4,5,6,7,8;
+  reset = 3;
+  sck   = 2;
+  mosi  = 9;
+  miso  = 11;
+;
+
+programmer
+  id     = "picoweb";
+  desc   = "Picoweb Programming Cable, http://www.picoweb.net/";
+  type   = "par";
+  connection_type = parallel;
+  reset  = 2;
+  sck    = 3;
+  mosi   = 4;
+  miso   = 13;
+;
+
+programmer
+  id    = "abcmini";
+  desc  = "ABCmini Board, aka Dick Smith HOTCHIP";
+  type  = "par";
+  connection_type = parallel;
+  reset = 4;
+  sck   = 3;
+  mosi  = 2;
+  miso  = 10;
+;
+
+programmer
+  id    = "futurlec";
+  desc  = "Futurlec.com programming cable.";
+  type  = "par";
+  connection_type = parallel;
+  reset = 3;
+  sck   = 2;
+  mosi  = 1;
+  miso  = 10;
+;
+
+
+# From the contributor of the "xil" jtag cable:
+# The "vcc" definition isn't really vcc (the cable gets its power from
+# the programming circuit) but is necessary to switch one of the
+# buffer lines (trying to add it to the "buff" lines doesn't work in 
+# avrdude versions before 5.5j).
+# With this, TMS connects to RESET, TDI to MOSI, TDO to MISO and TCK
+# to SCK (plus vcc/gnd of course)
+programmer
+  id    = "xil";
+  desc  = "Xilinx JTAG cable";
+  type  = "par";
+  connection_type = parallel;
+  mosi  = 2;
+  sck   = 3;
+  reset = 4;
+  buff  = 5;
+  miso  = 13;
+  vcc   = 6;
+;
+
+
+programmer
+  id = "dapa";
+  desc = "Direct AVR Parallel Access cable";
+  type = "par";
+  connection_type = parallel;
+  vcc   = 3;
+  reset = 16;
+  sck = 1;
+  mosi = 2;
+  miso = 11;
+;
+
+programmer
+  id    = "atisp";
+  desc  = "AT-ISP V1.1 programming cable for AVR-SDK1 from <http://micro-research.co.th/> micro-research.co.th";
+  type  = "par";
+  connection_type = parallel;
+  reset = ~6;
+  sck   = ~8;
+  mosi  = ~7;
+  miso  = ~10;
+;
+
+programmer
+  id    = "ere-isp-avr";
+  desc  = "ERE ISP-AVR <http://www.ere.co.th/download/sch050713.pdf>";
+  type  = "par";
+  connection_type = parallel;
+  reset = ~4;
+  sck   = 3;
+  mosi  = 2;
+  miso  = 10;
+;
+
+programmer
+  id    = "blaster";
+  desc  = "Altera ByteBlaster";
+  type  = "par";
+  connection_type = parallel;
+  sck   = 2;
+  miso  = 11;
+  reset = 3;
+  mosi  = 8;
+  buff  = 14;
+;
+
+# It is almost same as pony-stk200, except vcc on pin 5 to auto
+# disconnect port (download on http://electropol.free.fr/spip/spip.php?article27)
+programmer parent "pony-stk200"
+  id    = "frank-stk200";
+  desc  = "Frank STK200";
+  buff  = ; # delete buff pin assignment
+  vcc   = 5;
+;
+
+
+#This programmer bitbangs GPIO lines using the Linux sysfs GPIO interface
+#
+#To enable it set the configuration below to match the GPIO lines connected to the
+#relevant ISP header pins and uncomment the entry definition. In case you don't
+#have the required permissions to edit this system wide config file put the
+#entry in a separate <your name>.conf file and use it with -C+<your name>.conf
+#on the command line.
+#
+#To check if your avrdude build has support for the linuxgpio programmer compiled in,
+#use -c?type on the command line and look for linuxgpio in the list. If it's not available
+#you need pass the --enable-linuxgpio=yes option to configure and recompile avrdude.
+#
+#programmer
+#  id    = "linuxgpio";
+#  desc  = "Use the Linux sysfs interface to bitbang GPIO lines";
+#  type  = "linuxgpio";
+#  reset = ?;
+#  sck   = ?;
+#  mosi  = ?;
+#  miso  = ?;
+#;
+
+# some ultra cheap programmers use bitbanging on the 
+# serialport.
+#
+# PC - DB9 - Pins for RS232:
+#
+# GND   5   -- |O
+#              |   O| <-   9   RI
+# DTR   4   <- |O   |
+#              |   O| <-   8   CTS
+# TXD   3   <- |O   |
+#              |   O| ->   7   RTS
+# RXD   2   -> |O   |
+#              |   O| <-   6   DSR
+# DCD   1   -> |O
+#
+# Using RXD is currently not supported.
+# Using RI is not supported under Win32 but is supported under Posix.
+
+# serial ponyprog design (dasa2 in uisp)
+# reset=!txd sck=rts mosi=dtr miso=cts
+
+programmer
+  id    = "ponyser";
+  desc  = "design ponyprog serial, reset=!txd sck=rts mosi=dtr miso=cts";
+  type  = "serbb";
+  connection_type = serial;
+  reset = ~3;
+  sck   = 7;
+  mosi  = 4;
+  miso  = 8;
+;
+
+# Same as above, different name
+# reset=!txd sck=rts mosi=dtr miso=cts
+
+programmer parent "ponyser"
+  id    = "siprog";
+  desc  = "Lancos SI-Prog <http://www.lancos.com/siprogsch.html>";
+;
+
+# unknown (dasa in uisp)
+# reset=rts sck=dtr mosi=txd miso=cts
+
+programmer
+  id    = "dasa";
+  desc  = "serial port banging, reset=rts sck=dtr mosi=txd miso=cts";
+  type  = "serbb";
+  connection_type = serial;
+  reset = 7;
+  sck   = 4;
+  mosi  = 3;
+  miso  = 8;
+;
+
+# unknown (dasa3 in uisp)
+# reset=!dtr sck=rts mosi=txd miso=cts
+
+programmer
+  id    = "dasa3";
+  desc  = "serial port banging, reset=!dtr sck=rts mosi=txd miso=cts";
+  type  = "serbb";
+  connection_type = serial;
+  reset = ~4;
+  sck   = 7;
+  mosi  = 3;
+  miso  = 8;
+;
+
+# C2N232i (jumper configuration "auto")
+# reset=dtr sck=!rts mosi=!txd miso=!cts
+
+programmer
+  id    = "c2n232i";
+  desc  = "serial port banging, reset=dtr sck=!rts mosi=!txd miso=!cts";
+  type  = "serbb";
+  connection_type = serial;
+  reset = 4;
+  sck   = ~7;
+  mosi  = ~3;
+  miso  = ~8;
+;
+
+#
+# PART DEFINITIONS
+#
+
+
+#------------------------------------------------------------
+# ATmega8
+#------------------------------------------------------------
+
+part
+    id               = "m8";
+    desc             = "ATmega8";
+    stk500_devcode   = 0x70;
+    avr910_devcode   = 0x76;
+    signature        = 0x1e 0x93 0x07;
+    pagel            = 0xd7;
+    bs2              = 0xc2;
+    chip_erase_delay = 10000;
+    pgm_enable       = "1 0 1 0  1 1 0 0    0 1 0 1  0 0 1 1",
+                       "x x x x  x x x x    x x x x  x x x x";
+
+    chip_erase       = "1 0 1 0  1 1 0 0    1 0 0 x  x x x x",
+                       "x x x x  x x x x    x x x x  x x x x";
+
+    timeout		= 200;
+    stabdelay		= 100;
+    cmdexedelay		= 25;
+    synchloops		= 32;
+    bytedelay		= 0;
+    pollindex		= 3;
+    pollvalue		= 0x53;
+    predelay		= 1;
+    postdelay		= 1;
+    pollmethod		= 0;
+
+    pp_controlstack     =
+	0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+	0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+	0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+	0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+    hventerstabdelay    = 100;
+    progmodedelay       = 0;
+    latchcycles         = 5;
+    togglevtg           = 1;
+    poweroffdelay       = 15;
+    resetdelayms        = 2;
+    resetdelayus        = 0;
+    hvleavestabdelay    = 15;
+    resetdelay          = 15;
+    chiperasepulsewidth = 0;
+    chiperasepolltimeout = 10;
+    programfusepulsewidth = 0;
+    programfusepolltimeout = 5;
+    programlockpulsewidth = 0;
+    programlockpolltimeout = 5;
+
+    memory "eeprom"
+        size            = 512;
+        page_size       = 4;
+        min_write_delay = 9000;
+        max_write_delay = 9000;
+        readback_p1     = 0xff;
+        readback_p2     = 0xff;
+	read            = "  1   0   1   0      0   0   0   0",
+                          "  0   0   x   x      x   x   x  a8",
+                          " a7  a6  a5  a4     a3  a2  a1  a0",
+                          "  o   o   o   o      o   o   o   o";
+
+	write           = "  1   1   0   0      0   0   0   0",
+                          "  0   0   x   x      x   x   x  a8",
+                          " a7  a6  a5  a4     a3  a2  a1  a0", 
+                          "  i   i   i   i      i   i   i   i";
+
+	mode		= 0x04;
+	delay		= 20;
+	blocksize	= 128;
+	readsize	= 256;
+      ;
+    memory "flash"
+        paged           = yes;
+        size            = 8192;
+        page_size       = 64;
+        num_pages       = 128;
+        min_write_delay = 4500;
+        max_write_delay = 4500;
+        readback_p1     = 0xff;
+        readback_p2     = 0x00;
+        read_lo         = "  0   0   1   0    0   0   0   0",
+                          "  0   0   0   0  a11 a10  a9  a8",
+                          " a7  a6  a5  a4   a3  a2  a1  a0",
+                          "  o   o   o   o    o   o   o   o";
+
+        read_hi         = "  0   0   1   0    1   0   0   0",
+                          "  0   0   0   0  a11 a10  a9  a8",
+                          " a7  a6  a5  a4   a3  a2  a1  a0",
+                          "  o   o   o   o    o   o   o   o";
+
+        loadpage_lo     = "  0   1   0   0      0   0   0   0",
+                          "  0   0   0   0      x   x   x   x",
+                          "  x   x   x  a4     a3  a2  a1  a0",
+                          "  i   i   i   i      i   i   i   i";
+
+        loadpage_hi     = "  0   1   0   0      1   0   0   0",
+                          "  0   0   0   0      x   x   x   x",
+                          "  x   x   x  a4     a3  a2  a1  a0",
+                          "  i   i   i   i      i   i   i   i";
+
+        writepage       = "  0   1   0   0      1   1   0   0",
+                          "  0   0   0   0    a11 a10  a9  a8",
+                          " a7  a6  a5   x      x   x   x   x",
+                          "  x   x   x   x      x   x   x   x";
+
+	mode		= 0x21;
+	delay		= 10;
+	blocksize	= 64;
+	readsize	= 256;
+      ;
+
+    memory "lfuse"
+        size            = 1;
+        min_write_delay = 2000;
+        max_write_delay = 2000;
+        read            = "0 1 0 1  0 0 0 0   0 0 0 0  0 0 0 0",
+                          "x x x x  x x x x   o o o o  o o o o";
+
+        write           = "1 0 1 0  1 1 0 0   1 0 1 0  0 0 0 0",
+                          "x x x x  x x x x   i i i i  i i i i";
+      ;
+
+    memory "hfuse"
+        size            = 1;
+        min_write_delay = 2000;
+        max_write_delay = 2000;
+        read            = "0 1 0 1  1 0 0 0   0 0 0 0  1 0 0 0",
+                          "x x x x  x x x x   o o o o  o o o o";
+
+        write           = "1 0 1 0  1 1 0 0   1 0 1 0  1 0 0 0",
+                          "x x x x  x x x x   i i i i  i i i i";
+      ;
+      
+    memory "efuse"
+        size            = 0;
+      ;  
+
+    memory "lock"
+        size            = 1;
+        min_write_delay = 2000;
+        max_write_delay = 2000;
+        read            = "0 1 0 1  1 0 0 0   0 0 0 0  0 0 0 0",
+                          "x x x x  x x x x   x x o o  o o o o";
+
+        write           = "1 0 1 0  1 1 0 0   1 1 1 x  x x x x",
+                          "x x x x  x x x x   1 1 i i  i i i i";
+      ;
+
+    memory "calibration"
+        size            = 4;
+        read            = "0  0  1  1   1  0  0  0   0  0  x  x   x  x  x  x",
+                          "0  0  0  0   0  0 a1 a0   o  o  o  o   o  o  o  o";
+      ;
+
+    memory "signature"
+        size            = 3;
+        read            = "0  0  1  1   0  0  0  0   x  x  x  x   x  x  x  x",
+                          "x  x  x  x   x  x a1 a0   o  o  o  o   o  o  o  o";
+      ;
+  ;
+
+
+#------------------------------------------------------------
+# ATmega48
+#------------------------------------------------------------
+
+part
+    id               = "m48";
+    desc             = "ATmega48";
+     has_debugwire = yes;
+     flash_instr   = 0xB6, 0x01, 0x11;
+     eeprom_instr  = 0xBD, 0xF2, 0xBD, 0xE1, 0xBB, 0xCF, 0xB4, 0x00,
+	             0xBE, 0x01, 0xB6, 0x01, 0xBC, 0x00, 0xBB, 0xBF,
+	             0x99, 0xF9, 0xBB, 0xAF;
+    stk500_devcode   = 0x59;
+#    avr910_devcode   = 0x;
+    signature        = 0x1e 0x92 0x05;
+    pagel            = 0xd7;
+    bs2              = 0xc2;
+    chip_erase_delay = 45000;
+    pgm_enable       = "1 0 1 0  1 1 0 0    0 1 0 1  0 0 1 1",
+                       "x x x x  x x x x    x x x x  x x x x";
+
+    chip_erase       = "1 0 1 0  1 1 0 0    1 0 0 x  x x x x",
+                       "x x x x  x x x x    x x x x  x x x x";
+
+    timeout		= 200;
+    stabdelay		= 100;
+    cmdexedelay		= 25;
+    synchloops		= 32;
+    bytedelay		= 0;
+    pollindex		= 3;
+    pollvalue		= 0x53;
+    predelay		= 1;
+    postdelay		= 1;
+    pollmethod		= 1;
+
+    pp_controlstack     =
+	0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+	0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+	0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+	0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+    hventerstabdelay    = 100;
+    progmodedelay       = 0;
+    latchcycles         = 5;
+    togglevtg           = 1;
+    poweroffdelay       = 15;
+    resetdelayms        = 1;
+    resetdelayus        = 0;
+    hvleavestabdelay    = 15;
+    resetdelay          = 15;
+    chiperasepulsewidth = 0;
+    chiperasepolltimeout = 10;
+    programfusepulsewidth = 0;
+    programfusepolltimeout = 5;
+    programlockpulsewidth = 0;
+    programlockpolltimeout = 5;
+
+    ocdrev              = 1;
+
+    memory "eeprom"
+        paged           = no;
+        page_size       = 4;
+        size            = 256;
+        min_write_delay = 3600;
+        max_write_delay = 3600;
+        readback_p1     = 0xff;
+        readback_p2     = 0xff;
+	read            = "  1   0   1   0      0   0   0   0",
+                          "  0   0   0   x      x   x   x   x",
+                          " a7  a6  a5  a4     a3  a2  a1  a0",
+                          "  o   o   o   o      o   o   o   o";
+
+	write           = "  1   1   0   0      0   0   0   0",
+                          "  0   0   0   x      x   x   x   x",
+                          " a7  a6  a5  a4     a3  a2  a1  a0", 
+                          "  i   i   i   i      i   i   i   i";
+
+	loadpage_lo	= "  1   1   0   0      0   0   0   1",
+			  "  0   0   0   0      0   0   0   0",
+			  "  0   0   0   0      0   0  a1  a0",
+			  "  i   i   i   i      i   i   i   i";
+
+	writepage	= "  1   1   0   0      0   0   1   0",
+			  "  0   0   x   x      x   x   x   x",
+			  " a7  a6  a5  a4     a3  a2   0   0",
+			  "  x   x   x   x      x   x   x   x";
+
+	mode		= 0x41;
+	delay		= 20;
+	blocksize	= 4;
+	readsize	= 256;
+      ;
+    memory "flash"
+        paged           = yes;
+        size            = 4096;
+        page_size       = 64;
+        num_pages       = 64;
+        min_write_delay = 4500;
+        max_write_delay = 4500;
+        readback_p1     = 0x00;
+        readback_p2     = 0x00;
+        read_lo         = "  0   0   1   0    0   0   0   0",
+                          "  0   0   0   0    0 a10  a9  a8",
+                          " a7  a6  a5  a4   a3  a2  a1  a0",
+                          "  o   o   o   o    o   o   o   o";
+
+        read_hi         = "  0   0   1   0    1   0   0   0",
+                          "  0   0   0   0    0 a10  a9  a8",
+                          " a7  a6  a5  a4   a3  a2  a1  a0",
+                          "  o   o   o   o    o   o   o   o";
+
+        loadpage_lo     = "  0   1   0   0      0   0   0   0",
+                          "  0   0   0   x      x   x   x   x",
+                          "  x   x   x  a4     a3  a2  a1  a0",
+                          "  i   i   i   i      i   i   i   i";
+
+        loadpage_hi     = "  0   1   0   0      1   0   0   0",
+                          "  0   0   0   x      x   x   x   x",
+                          "  x   x   x  a4     a3  a2  a1  a0",
+                          "  i   i   i   i      i   i   i   i";
+
+        writepage       = "  0   1   0   0      1   1   0   0",
+                          "  0   0   0   0      0 a10  a9  a8",
+                          " a7  a6  a5   x      x   x   x   x",
+                          "  x   x   x   x      x   x   x   x";
+
+	mode		= 0x41;
+	delay		= 6;
+	blocksize	= 64;
+	readsize	= 256;
+      ;
+
+    memory "lfuse"
+        size            = 1;
+        min_write_delay = 4500;
+        max_write_delay = 4500;
+        read            = "0 1 0 1  0 0 0 0   0 0 0 0  0 0 0 0",
+                          "x x x x  x x x x   o o o o  o o o o";
+
+        write           = "1 0 1 0  1 1 0 0   1 0 1 0  0 0 0 0",
+                          "x x x x  x x x x   i i i i  i i i i";
+      ;
+
+    memory "hfuse"
+        size            = 1;
+        min_write_delay = 4500;
+        max_write_delay = 4500;
+        read            = "0 1 0 1  1 0 0 0   0 0 0 0  1 0 0 0",
+                          "x x x x  x x x x   o o o o  o o o o";
+
+        write           = "1 0 1 0  1 1 0 0   1 0 1 0  1 0 0 0",
+                          "x x x x  x x x x   i i i i  i i i i";
+      ;
+
+    memory "efuse"
+        size            = 1;
+        min_write_delay = 4500;
+        max_write_delay = 4500;
+        read            = "0 1 0 1  0 0 0 0   0 0 0 0  1 0 0 0",
+                          "x x x x  x x x x   o o o o  o o o o";
+
+        write           = "1 0 1 0  1 1 0 0   1 0 1 0  0 1 0 0",
+                          "x x x x  x x x x   x x x x  x x x i";
+      ;
+
+    memory "lock"
+        size            = 1;
+        min_write_delay = 4500;
+        max_write_delay = 4500;
+        read            = "0 1 0 1  1 0 0 0   0 0 0 0  0 0 0 0",
+                          "x x x x  x x x x   x x o o  o o o o";
+
+        write           = "1 0 1 0  1 1 0 0   1 1 1 x  x x x x",
+                          "x x x x  x x x x   1 1 i i  i i i i";
+      ;
+
+    memory "calibration"
+        size            = 1;
+        read            = "0  0  1  1   1  0  0  0   0  0  0  x   x  x  x  x",
+                          "0  0  0  0   0  0  0  0   o  o  o  o   o  o  o  o";
+      ;
+
+    memory "signature"
+        size            = 3;
+        read            = "0  0  1  1   0  0  0  0   0  0  0  x   x  x  x  x",
+                          "x  x  x  x   x  x a1 a0   o  o  o  o   o  o  o  o";
+      ;
+  ;
+
+#------------------------------------------------------------
+# ATmega48P
+#------------------------------------------------------------
+
+part parent "m48"
+    id               = "m48p";
+    desc             = "ATmega48P";
+    signature        = 0x1e 0x92 0x0a;
+
+    ocdrev              = 1;
+  ;
+
+#------------------------------------------------------------
+# ATmega48PB
+#------------------------------------------------------------
+
+part parent "m48"
+    id               = "m48pb";
+    desc             = "ATmega48PB";
+    signature        = 0x1e 0x92 0x10;
+
+    ocdrev              = 1;
+  ;
+
+#------------------------------------------------------------
+# ATmega88
+#------------------------------------------------------------
+
+part
+    id               = "m88";
+    desc             = "ATmega88";
+     has_debugwire = yes;
+     flash_instr   = 0xB6, 0x01, 0x11;
+     eeprom_instr  = 0xBD, 0xF2, 0xBD, 0xE1, 0xBB, 0xCF, 0xB4, 0x00,
+	             0xBE, 0x01, 0xB6, 0x01, 0xBC, 0x00, 0xBB, 0xBF,
+	             0x99, 0xF9, 0xBB, 0xAF;
+    stk500_devcode   = 0x73;
+#    avr910_devcode   = 0x;
+    signature        = 0x1e 0x93 0x0a;
+    pagel            = 0xd7;
+    bs2              = 0xc2;
+    chip_erase_delay = 9000;
+    pgm_enable       = "1 0 1 0  1 1 0 0    0 1 0 1  0 0 1 1",
+                       "x x x x  x x x x    x x x x  x x x x";
+
+    chip_erase       = "1 0 1 0  1 1 0 0    1 0 0 x  x x x x",
+                       "x x x x  x x x x    x x x x  x x x x";
+
+    timeout		= 200;
+    stabdelay		= 100;
+    cmdexedelay		= 25;
+    synchloops		= 32;
+    bytedelay		= 0;
+    pollindex		= 3;
+    pollvalue		= 0x53;
+    predelay		= 1;
+    postdelay		= 1;
+    pollmethod		= 1;
+
+    pp_controlstack     =
+	0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+	0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+	0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+	0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+    hventerstabdelay    = 100;
+    progmodedelay       = 0;
+    latchcycles         = 5;
+    togglevtg           = 1;
+    poweroffdelay       = 15;
+    resetdelayms        = 1;
+    resetdelayus        = 0;
+    hvleavestabdelay    = 15;
+    resetdelay          = 15;
+    chiperasepulsewidth = 0;
+    chiperasepolltimeout = 10;
+    programfusepulsewidth = 0;
+    programfusepolltimeout = 5;
+    programlockpulsewidth = 0;
+    programlockpolltimeout = 5;
+
+    ocdrev              = 1;
+
+    memory "eeprom"
+        paged           = no;
+        page_size       = 4;
+        size            = 512;
+        min_write_delay = 3600;
+        max_write_delay = 3600;
+        readback_p1     = 0xff;
+        readback_p2     = 0xff;
+	read            = "  1   0   1   0      0   0   0   0",
+                          "  0   0   0   x      x   x   x  a8",
+                          " a7  a6  a5  a4     a3  a2  a1  a0",
+                          "  o   o   o   o      o   o   o   o";
+
+	write           = "  1   1   0   0      0   0   0   0",
+                          "  0   0   0   x      x   x   x  a8",
+                          " a7  a6  a5  a4     a3  a2  a1  a0", 
+                          "  i   i   i   i      i   i   i   i";
+
+	loadpage_lo	= "  1   1   0   0      0   0   0   1",
+			  "  0   0   0   0      0   0   0   0",
+			  "  0   0   0   0      0   0  a1  a0",
+			  "  i   i   i   i      i   i   i   i";
+
+	writepage	= "  1   1   0   0      0   0   1   0",
+			  "  0   0   x   x      x   x   x  a8",
+			  " a7  a6  a5  a4     a3  a2   0   0",
+			  "  x   x   x   x      x   x   x   x";
+
+	mode		= 0x41;
+	delay		= 20;
+	blocksize	= 4;
+	readsize	= 256;
+      ;
+    memory "flash"
+        paged           = yes;
+        size            = 8192;
+        page_size       = 64;
+        num_pages       = 128;
+        min_write_delay = 4500;
+        max_write_delay = 4500;
+        readback_p1     = 0xff;
+        readback_p2     = 0xff;
+        read_lo         = "  0   0   1   0    0   0   0   0",
+                          "  0   0   0   0  a11 a10  a9  a8",
+                          " a7  a6  a5  a4   a3  a2  a1  a0",
+                          "  o   o   o   o    o   o   o   o";
+
+        read_hi         = "  0   0   1   0    1   0   0   0",
+                          "  0   0   0   0  a11 a10  a9  a8",
+                          " a7  a6  a5  a4   a3  a2  a1  a0",
+                          "  o   o   o   o    o   o   o   o";
+
+        loadpage_lo     = "  0   1   0   0      0   0   0   0",
+                          "  0   0   0   x      x   x   x   x",
+                          "  x   x   x  a4     a3  a2  a1  a0",
+                          "  i   i   i   i      i   i   i   i";
+
+        loadpage_hi     = "  0   1   0   0      1   0   0   0",
+                          "  0   0   0   x      x   x   x   x",
+                          "  x   x   x  a4     a3  a2  a1  a0",
+                          "  i   i   i   i      i   i   i   i";
+
+        writepage       = "  0   1   0   0      1   1   0   0",
+                          "  0   0   0   0    a11 a10  a9  a8",
+                          " a7  a6  a5   x      x   x   x   x",
+                          "  x   x   x   x      x   x   x   x";
+
+	mode		= 0x41;
+	delay		= 6;
+	blocksize	= 64;
+	readsize	= 256;
+      ;
+
+    memory "lfuse"
+        size            = 1;
+        min_write_delay = 4500;
+        max_write_delay = 4500;
+        read            = "0 1 0 1  0 0 0 0   0 0 0 0  0 0 0 0",
+                          "x x x x  x x x x   o o o o  o o o o";
+
+        write           = "1 0 1 0  1 1 0 0   1 0 1 0  0 0 0 0",
+                          "x x x x  x x x x   i i i i  i i i i";
+      ;
+
+    memory "hfuse"
+        size            = 1;
+        min_write_delay = 4500;
+        max_write_delay = 4500;
+        read            = "0 1 0 1  1 0 0 0   0 0 0 0  1 0 0 0",
+                          "x x x x  x x x x   o o o o  o o o o";
+
+        write           = "1 0 1 0  1 1 0 0   1 0 1 0  1 0 0 0",
+                          "x x x x  x x x x   i i i i  i i i i";
+      ;
+
+    memory "efuse"
+        size            = 1;
+        min_write_delay = 4500;
+        max_write_delay = 4500;
+        read            = "0 1 0 1  0 0 0 0   0 0 0 0  1 0 0 0",
+                          "x x x x  x x x x   o o o o  o o o o";
+
+        write           = "1 0 1 0  1 1 0 0   1 0 1 0  0 1 0 0",
+                          "x x x x  x x x x   x x x x  x i i i";
+      ;
+
+    memory "lock"
+        size            = 1;
+        min_write_delay = 4500;
+        max_write_delay = 4500;
+        read            = "0 1 0 1  1 0 0 0   0 0 0 0  0 0 0 0",
+                          "x x x x  x x x x   x x o o  o o o o";
+
+        write           = "1 0 1 0  1 1 0 0   1 1 1 x  x x x x",
+                          "x x x x  x x x x   1 1 i i  i i i i";
+      ;
+
+    memory "calibration"
+        size            = 1;
+        read            = "0  0  1  1   1  0  0  0   0  0  0  x   x  x  x  x",
+                          "0  0  0  0   0  0  0  0   o  o  o  o   o  o  o  o";
+      ;
+
+    memory "signature"
+        size            = 3;
+        read            = "0  0  1  1   0  0  0  0   0  0  0  x   x  x  x  x",
+                          "x  x  x  x   x  x a1 a0   o  o  o  o   o  o  o  o";
+      ;
+  ;
+
+#------------------------------------------------------------
+# ATmega88P
+#------------------------------------------------------------
+
+part parent "m88"
+    id               = "m88p";
+    desc             = "ATmega88P";
+    signature        = 0x1e 0x93 0x0f;
+
+    ocdrev              = 1;
+  ;
+
+#------------------------------------------------------------
+# ATmega88PB
+#------------------------------------------------------------
+
+part parent "m88"
+    id               = "m88pb";
+    desc             = "ATmega88PB";
+    signature        = 0x1e 0x93 0x16;
+
+    ocdrev              = 1;
+  ;
+
+#------------------------------------------------------------
+# ATmega168
+#------------------------------------------------------------
+
+part
+    id              = "m168";
+    desc            = "ATmega168";
+     has_debugwire = yes;
+     flash_instr   = 0xB6, 0x01, 0x11;
+     eeprom_instr  = 0xBD, 0xF2, 0xBD, 0xE1, 0xBB, 0xCF, 0xB4, 0x00,
+	             0xBE, 0x01, 0xB6, 0x01, 0xBC, 0x00, 0xBB, 0xBF,
+	             0x99, 0xF9, 0xBB, 0xAF;
+    stk500_devcode  = 0x86;
+    # avr910_devcode = 0x;
+    signature       = 0x1e 0x94 0x06;
+    pagel           = 0xd7;
+    bs2             = 0xc2;
+    chip_erase_delay = 9000;
+    pgm_enable       = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+                       "x x x x x x x x x x x x x x x x";
+
+    chip_erase       = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+                       "x x x x x x x x x x x x x x x x";
+
+    timeout         = 200;
+    stabdelay       = 100;
+    cmdexedelay     = 25;
+    synchloops      = 32;
+    bytedelay       = 0;
+    pollindex       = 3;
+    pollvalue       = 0x53;
+    predelay        = 1;
+    postdelay       = 1;
+    pollmethod      = 1;
+
+    pp_controlstack     =
+	0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+	0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+	0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+	0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+    hventerstabdelay    = 100;
+    progmodedelay       = 0;
+    latchcycles         = 5;
+    togglevtg           = 1;
+    poweroffdelay       = 15;
+    resetdelayms        = 1;
+    resetdelayus        = 0;
+    hvleavestabdelay    = 15;
+    resetdelay          = 15;
+    chiperasepulsewidth = 0;
+    chiperasepolltimeout = 10;
+    programfusepulsewidth = 0;
+    programfusepolltimeout = 5;
+    programlockpulsewidth = 0;
+    programlockpolltimeout = 5;
+
+    ocdrev              = 1;
+
+    memory "eeprom"
+        paged           = no;
+        page_size       = 4;
+        size            = 512;
+        min_write_delay = 3600;
+        max_write_delay = 3600;
+        readback_p1     = 0xff;
+        readback_p2     = 0xff;
+        read            = " 1 0 1 0 0 0 0 0",
+                          " 0 0 0 x x x x a8",
+                          " a7 a6 a5 a4 a3 a2 a1 a0",
+                          " o o o o o o o o";
+    
+        write           = " 1 1 0 0 0 0 0 0",
+                          " 0 0 0 x x x x a8",
+                          " a7 a6 a5 a4 a3 a2 a1 a0",
+                          " i i i i i i i i";
+
+	loadpage_lo	= "  1   1   0   0      0   0   0   1",
+			  "  0   0   0   0      0   0   0   0",
+			  "  0   0   0   0      0   0  a1  a0",
+			  "  i   i   i   i      i   i   i   i";
+
+	writepage	= "  1   1   0   0      0   0   1   0",
+			  "  0   0   x   x      x   x   x  a8",
+			  " a7  a6  a5  a4     a3  a2   0   0",
+			  "  x   x   x   x      x   x   x   x";
+
+	mode		= 0x41;
+	delay		= 20;
+	blocksize	= 4;
+	readsize	= 256;
+        ;
+
+    memory "flash"
+        paged           = yes;
+        size            = 16384;
+        page_size       = 128;
+        num_pages       = 128;
+        min_write_delay = 4500;
+        max_write_delay = 4500;
+        readback_p1     = 0xff;
+        readback_p2     = 0xff;
+        read_lo         = " 0 0 1 0 0 0 0 0",
+                          " 0 0 0 a12 a11 a10 a9 a8",
+                          " a7 a6 a5 a4 a3 a2 a1 a0",
+                          " o o o o o o o o";
+        
+        read_hi          = " 0 0 1 0 1 0 0 0",
+                           " 0 0 0 a12 a11 a10 a9 a8",
+                           " a7 a6 a5 a4 a3 a2 a1 a0",
+                           " o o o o o o o o";
+        
+        loadpage_lo     = " 0 1 0 0 0 0 0 0",
+                          " 0 0 0 x x x x x",
+                          " x x a5 a4 a3 a2 a1 a0",
+                          " i i i i i i i i";
+        
+        loadpage_hi     = " 0 1 0 0 1 0 0 0",
+                          " 0 0 0 x x x x x",
+                          " x x a5 a4 a3 a2 a1 a0",
+                          " i i i i i i i i";
+        
+        writepage       = " 0 1 0 0 1 1 0 0",
+                          " 0 0 0 a12 a11 a10 a9 a8",
+                          " a7 a6 x x x x x x",
+                          " x x x x x x x x";
+
+        mode        = 0x41;
+        delay       = 6;
+        blocksize   = 128;
+        readsize    = 256;
+
+        ;
+        
+    memory "lfuse"
+        size            = 1;
+        min_write_delay = 4500;
+        max_write_delay = 4500;
+        read            = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+                          "x x x x x x x x o o o o o o o o";
+        
+        write           = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+                          "x x x x x x x x i i i i i i i i";
+        ;
+    
+    memory "hfuse"
+        size            = 1;
+        min_write_delay = 4500;
+        max_write_delay = 4500;
+        read            = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+                          "x x x x x x x x o o o o o o o o";
+        
+        write           = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+                          "x x x x x x x x i i i i i i i i";
+        ;
+    
+    memory "efuse"
+        size            = 1;
+        min_write_delay = 4500;
+        max_write_delay = 4500;
+        read            = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+                          "x x x x x x x x o o o o o o o o";
+        
+        write           = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+                          "x x x x x x x x x x x x x i i i";
+        ;
+    
+    memory "lock"
+        size            = 1;
+        min_write_delay = 4500;
+        max_write_delay = 4500;
+        read            = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+                          "x x x x x x x x x x o o o o o o";
+        
+        write           = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+                          "x x x x x x x x 1 1 i i i i i i";
+        ;
+    
+    memory "calibration"
+        size            = 1;
+        read            = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+                          "0 0 0 0 0 0 0 0 o o o o o o o o";
+        ;
+    
+    memory "signature"
+        size            = 3;
+        read            = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+                          "x x x x x x a1 a0 o o o o o o o o";
+        ;
+;
+
+#------------------------------------------------------------
+# ATmega168P
+#------------------------------------------------------------
+
+part parent "m168"
+    id              = "m168p";
+    desc            = "ATmega168P";
+    signature       = 0x1e 0x94 0x0b;
+
+    ocdrev              = 1;
+;
+
+#------------------------------------------------------------
+# ATmega168PB
+#------------------------------------------------------------
+
+part parent "m168"
+    id              = "m168pb";
+    desc            = "ATmega168PB";
+    signature       = 0x1e 0x94 0x15;
+
+    ocdrev              = 1;
+;
+
+
+#------------------------------------------------------------
+# ATmega328
+#------------------------------------------------------------
+
+part
+    id			= "m328";
+    desc		= "ATmega328";
+    has_debugwire	= yes;
+    flash_instr		= 0xB6, 0x01, 0x11;
+    eeprom_instr	= 0xBD, 0xF2, 0xBD, 0xE1, 0xBB, 0xCF, 0xB4, 0x00,
+			  0xBE, 0x01, 0xB6, 0x01, 0xBC, 0x00, 0xBB, 0xBF,
+			  0x99, 0xF9, 0xBB, 0xAF;
+    stk500_devcode	= 0x86;
+    # avr910_devcode	= 0x;
+    signature		= 0x1e 0x95 0x14;
+    pagel		= 0xd7;
+    bs2			= 0xc2;
+    chip_erase_delay	= 9000;
+    pgm_enable = "1 0 1 0 1 1 0 0 0 1 0 1 0 0 1 1",
+		 "x x x x x x x x x x x x x x x x";
+
+    chip_erase = "1 0 1 0 1 1 0 0 1 0 0 x x x x x",
+		 "x x x x x x x x x x x x x x x x";
+
+    timeout	= 200;
+    stabdelay	= 100;
+    cmdexedelay	= 25;
+    synchloops	= 32;
+    bytedelay	= 0;
+    pollindex	= 3;
+    pollvalue	= 0x53;
+    predelay	= 1;
+    postdelay	= 1;
+    pollmethod	= 1;
+
+    pp_controlstack =
+	0x0E, 0x1E, 0x0F, 0x1F, 0x2E, 0x3E, 0x2F, 0x3F,
+	0x4E, 0x5E, 0x4F, 0x5F, 0x6E, 0x7E, 0x6F, 0x7F,
+	0x66, 0x76, 0x67, 0x77, 0x6A, 0x7A, 0x6B, 0x7B,
+	0xBE, 0xFD, 0x00, 0x01, 0x00, 0x00, 0x00, 0x00;
+    hventerstabdelay	= 100;
+    progmodedelay	= 0;
+    latchcycles		= 5;
+    togglevtg		= 1;
+    poweroffdelay	= 15;
+    resetdelayms	= 1;
+    resetdelayus	= 0;
+    hvleavestabdelay	= 15;
+    resetdelay		= 15;
+    chiperasepulsewidth	= 0;
+    chiperasepolltimeout = 10;
+    programfusepulsewidth = 0;
+    programfusepolltimeout = 5;
+    programlockpulsewidth = 0;
+    programlockpolltimeout = 5;
+
+    ocdrev              = 1;
+
+    memory "eeprom"
+	paged		= no;
+	page_size	= 4;
+	size		= 1024;
+	min_write_delay = 3600;
+	max_write_delay = 3600;
+	readback_p1	= 0xff;
+	readback_p2	= 0xff;
+	read = " 1 0 1 0 0 0 0 0",
+	       " 0 0 0 x x x a9 a8",
+	       " a7 a6 a5 a4 a3 a2 a1 a0",
+	       " o o o o o o o o";
+
+	write = " 1 1 0 0 0 0 0 0",
+	      	" 0 0 0 x x x a9 a8",
+		" a7 a6 a5 a4 a3 a2 a1 a0",
+		" i i i i i i i i";
+
+	loadpage_lo = " 1 1 0 0 0 0 0 1",
+		      " 0 0 0 0 0 0 0 0",
+		      " 0 0 0 0 0 0 a1 a0",
+		      " i i i i i i i i";
+
+	writepage = " 1 1 0 0 0 0 1 0",
+		    " 0 0 x x x x a9 a8",
+		    " a7 a6 a5 a4 a3 a2 0 0",
+		    " x x x x x x x x";
+
+	mode		= 0x41;
+	delay		= 20;
+	blocksize	= 4;
+	readsize	= 256;
+    ;
+
+    memory "flash"
+	paged		= yes;
+	size		= 32768;
+	page_size	= 128;
+	num_pages	= 256;
+	min_write_delay = 4500;
+	max_write_delay = 4500;
+	readback_p1	= 0xff;
+	readback_p2	= 0xff;
+	read_lo = " 0 0 1 0 0 0 0 0",
+		  " 0 0 a13 a12 a11 a10 a9 a8",
+		  " a7 a6 a5 a4 a3 a2 a1 a0",
+		  " o o o o o o o o";
+
+	read_hi = " 0 0 1 0 1 0 0 0",
+		  " 0 0 a13 a12 a11 a10 a9 a8",
+		  " a7 a6 a5 a4 a3 a2 a1 a0",
+		  " o o o o o o o o";
+
+	loadpage_lo = " 0 1 0 0 0 0 0 0",
+		      " 0 0 0 x x x x x",
+		      " x x a5 a4 a3 a2 a1 a0",
+		      " i i i i i i i i";
+
+	loadpage_hi = " 0 1 0 0 1 0 0 0",
+		      " 0 0 0 x x x x x",
+		      " x x a5 a4 a3 a2 a1 a0",
+		      " i i i i i i i i";
+
+	writepage = " 0 1 0 0 1 1 0 0",
+		    " 0 0 a13 a12 a11 a10 a9 a8",
+		    " a7 a6 x x x x x x",
+		    " x x x x x x x x";
+
+	mode		= 0x41;
+	delay		= 6;
+	blocksize	= 128;
+	readsize	= 256;
+
+    ;
+
+    memory "lfuse"
+	size = 1;
+	min_write_delay = 4500;
+	max_write_delay = 4500;
+	read = "0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0",
+	       "x x x x x x x x o o o o o o o o";
+
+	write = "1 0 1 0 1 1 0 0 1 0 1 0 0 0 0 0",
+	      	"x x x x x x x x i i i i i i i i";
+    ;
+
+    memory "hfuse"
+	size = 1;
+	min_write_delay = 4500;
+	max_write_delay = 4500;
+	read = "0 1 0 1 1 0 0 0 0 0 0 0 1 0 0 0",
+	       "x x x x x x x x o o o o o o o o";
+
+	write = "1 0 1 0 1 1 0 0 1 0 1 0 1 0 0 0",
+	      	"x x x x x x x x i i i i i i i i";
+    ;
+
+    memory "efuse"
+	size = 1;
+	min_write_delay = 4500;
+	max_write_delay = 4500;
+	read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+	       "x x x x x x x x o o o o o o o o";
+
+	write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+	      	"x x x x x x x x x x x x x i i i";
+    ;
+
+    memory "lock"
+	size = 1;
+	min_write_delay = 4500;
+	max_write_delay = 4500;
+	read = "0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0",
+	       "x x x x x x x x x x o o o o o o";
+
+	write = "1 0 1 0 1 1 0 0 1 1 1 x x x x x",
+	      	"x x x x x x x x 1 1 i i i i i i";
+    ;
+
+    memory "calibration"
+	size = 1;
+	read = "0 0 1 1 1 0 0 0 0 0 0 x x x x x",
+	       "0 0 0 0 0 0 0 0 o o o o o o o o";
+    ;
+
+    memory "signature"
+	size = 3;
+	read = "0 0 1 1 0 0 0 0 0 0 0 x x x x x",
+	       "x x x x x x a1 a0 o o o o o o o o";
+    ;
+;
+
+
+#------------------------------------------------------------
+# ATmega328P
+#------------------------------------------------------------
+
+part parent "m328"
+    id			= "m328p";
+    desc		= "ATmega328P";
+    signature		= 0x1e 0x95 0x0F;
+
+    ocdrev              = 1;
+;
+
+
+#------------------------------------------------------------
+# ATmega328PB
+#------------------------------------------------------------
+
+part parent "m328"
+    id			= "m328pb";
+    desc		= "ATmega328PB";
+    signature		= 0x1e 0x95 0x16;
+
+    ocdrev              = 1;
+
+    memory "efuse"
+  size = 1;
+  min_write_delay = 4500;
+  max_write_delay = 4500;
+  read = "0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0",
+          "x x x x x x x x o o o o o o o o";
+
+  write = "1 0 1 0 1 1 0 0 1 0 1 0 0 1 0 0",
+          "x x x x x x x x x x x x i i i i";
+    ;
+;
+
+# Linux GPIO definitions for avrdude & Raspberry Picoweb
+programmer
+  id    = "pi_spi";
+  desc  = "Use the Linux sysfs interface to bitbang GPIO lines";
+  type  = "linuxgpio";
+  reset = 12;
+  sck   = 24;
+  mosi  = 23;
+  miso  = 18;
+;
\ No newline at end of file
diff --git a/scripts/bootloader/optiboot_flash_atmega328pb_UART0_38400_8000000L.hex b/scripts/bootloader/optiboot_flash_atmega328pb_UART0_38400_8000000L.hex
new file mode 100644
index 0000000..5dff640
--- /dev/null
+++ b/scripts/bootloader/optiboot_flash_atmega328pb_UART0_38400_8000000L.hex
@@ -0,0 +1,32 @@
+:107E000001C0ABC0112484B7882361F0982F9A7009
+:107E1000923041F081FF02C097EF94BF282E80E09E
+:107E2000BFD0EEC085E08093810082E08093C000E7
+:107E300088E18093C10089E18093C40086E080934B
+:107E4000C2008EE0ADD0259A84E028E13EEF91E0BB
+:107E5000309385002093840096BBB09BFECF1D9A83
+:107E6000A8954091C00047FD02C0815089F78CD091
+:107E7000813461F489D0182F99D01238E9F0113883
+:107E800011F488E001C083E078D064C0823411F43A
+:107E900084E103C0853419F485E090D05BC085355A
+:107EA00039F472D0C82F70D0D82FCC0FDD1F51C03D
+:107EB000863521F484E082D080E0E6CF843661F517
+:107EC00063D062D0D82E60D0F82E00E011E05CD0F4
+:107ED000F80181938F01DE12FACF68D0F5E4FF122A
+:107EE00001C0FFCF40E050E063E0CE0136D07E011C
+:107EF00000E011E0F801419151918F0161E0C7016B
+:107F00002CD0F2E0EF0EF11CD012F4CF40E050E0A4
+:107F100065E0CE0122D01EC0843771F435D034D054
+:107F2000F82E32D043D08E01F80185918F0125D0F3
+:107F3000FA94F110F9CF0EC0853739F437D08EE1BD
+:107F40001CD085E91AD086E19FCF813511F488E0F5
+:107F500027D02CD080E111D08ACFFC010A0167BF65
+:107F6000E895112407B600FCFDCF667029F0452B7B
+:107F700019F481E187BFE89508959091C00095FFBD
+:107F8000FCCF8093C60008958091C00087FFFCCF8E
+:107F90008091C00084FD01C0A8958091C60008951D
+:107FA000E0E6F0E098E1908380830895EDDF803291
+:107FB00019F088E0F5DFFFCF84E1DFCFCF93C82F42
+:0A7FC000E3DFC150E9F7CF91F1CFE4
+:027FFE00000879
+:0400000300007E007B
+:00000001FF
diff --git a/scripts/upload-firmware.sh b/scripts/upload-firmware.sh
index 00fcc83..3ea0d68 100644
--- a/scripts/upload-firmware.sh
+++ b/scripts/upload-firmware.sh
@@ -19,16 +19,19 @@ Usage:
 EOF
 
 # Default values
-serialdevice=COM3
+serialdevice=/dev/ttyUSB0
 board=m328pb
 lowfuse=0xE2
 highfuse=0xD6
 exfuse=0xF6
-firmwarebin=Pyr0_Piezo_Sensor_m328pb_v2.x.x.hex
+firmwarebin=../firmware/Compiled-Firmware/pyr0_piezo_firmware_v2.3.2.hex
 
 # Programming functions
 program-icsp() {
-  avrdude -c avrisp -p $board -b19200 -P$serialdevice -U lfuse:w:$lowfuse:m -U hfuse:w:$highfuse:m -U efuse:w:$exfuse:m -U flash:w:$firmwarebin -v
+  #avrdude -c avrisp -p $board -b19200 -P$serialdevice -U lfuse:w:$lowfuse:m -U hfuse:w:$highfuse:m -U efuse:w:$exfuse:m -U flash:w:$firmwarebin -v
+  avrdude -Cbootloader/MiniCire-avrdude.conf -v -patmega328pb -cstk500v1 -P$serialdevice -b19200 -e -Ulock:w:0x3f:m -Uefuse:w:0b11110110:m -Uhfuse:w:0xd6:m -Ulfuse:w:0xe2:m 
+  avrdude -Cbootloader/MiniCire-avrdude.conf -v -patmega328pb -cstk500v1 -P$serialdevice -b19200 -Uflash:w:bootloader/optiboot_flash_atmega328pb_UART0_38400_8000000L.hex:i -Ulock:w:0x0f:m
+  avrdude -Cbootloader/MiniCire-avrdude.conf -v -c stk500v1 -p $board -b19200 -P$serialdevice -U flash:w:$firmwarebin
 }
 
 program-uart() {
@@ -43,11 +46,11 @@ while getopts ":b:d:f:i:u" opt
       h)  echo "$usage"
         exit
         ;;
-      b)  board="$2";
+      b)  board="$@";
         shift ;;
-      d)  serialdevice="$2";
+      d)  serialdevice="$@";
         shift ;;
-      f)  firmwarebin="$2";
+      f)  firmwarebin="$@";
         shift ;;
       i)  program-icsp
         shift ;;